MOTOROLA AET-3047 6U VME Front Panel Transition I O Interface Module

  • 0 reviews
  • Write a review
    • Product Code: AET-3047
    • Availability: In Stock

    Purchase Attributes：Original, Brand New

    Service Attributes

    ▷ Stock & Logistics：Fast Delivery

    ▷ After-sales Guarantee：12 Months Warranty

    Operating Temperature: Industrial standard -20℃ ~ +70℃ forced air cooling

    Storage Temperature: -40℃ ~ +85℃; 

    Relative Humidity: 5% ~ 95% RH non-condensing

    • Mechanical Dimension: 233.4mm(H) × 160mm(W) × 18mm(D)

    MOTOROLA AET-3047 6U VME Front Panel Transition I/O Interface Module For MVME2600/MVME2700 Series SBC
    Manufacturer: Motorola Computer Group, later Emerson Embedded Computing
    Model: AET-3047 VME Signal Transition Breakout Board
    Product Type: Single-height 6U VMEbus passive transition slave module, front-panel signal breakout accessory board
    Matching Host: MVME260x, MVME270x, MVME360x, MVME460x PowerPC VME single board computers
    Core Function: Rear P2 VME bus signal routing to front industrial standard connectors, breakout Ethernet, serial, parallel printer and field peripheral signals; passive wiring conversion without signal processing, full ESD surge protection, simplify field cable wiring for DCS and ATE systems
    1. Product Overview
    AET-3047 is a passive front-panel transition breakout module developed by Motorola exclusively for the MVME2600/MVME2700 series PowerPC VME single board computers. It adopts a fully passive circuit design without any processing chips, only responsible for bridging the rear P2 VME bus signal pins of the main control board to standard external connectors on the front panel, realizing convenient on-site wiring without modifying the main SBC hardware. The board integrates 3×RJ45 Ethernet ports, 1×DB25 multi-mode serial port, 1×DB36 Centronics parallel printer port and dedicated reserved signal terminals for peripheral expansion. All signal lines are equipped with independent ESD and surge suppression circuits to eliminate industrial ground loop interference and protect the host mainboard from external signal overvoltage damage. As a pure signal routing transition board, it cannot independently execute control logic or data processing, and must be installed in the same VME chassis together with a compatible MVME PowerPC host board to work normally. It greatly simplifies the wiring layout of thermal power DCS, petrochemical distributed control and aerospace automatic test benches, and shortens equipment installation and maintenance time. This product has been discontinued, and only refurbished and surplus spare parts are available for legacy industrial control system maintenance.
    2. Complete Technical Specifications
    • Circuit Type: Fully passive wiring board, no CPU, FPGA or signal processing chips
    • VME Interface: Rear P2 connector direct signal mapping, A16/A24/A32 signal pin one-to-one routing
    • Front Panel External Ports: 3×RJ45 10/100Base-T Ethernet, 1×DB25 RS232/422 serial, 1×DB36 Centronics parallel printer
    • Signal Protection: ±15kV contact ESD, ±25kV air discharge ESD, 2kV surge suppression for all external signal lines
    • Isolation Design: Independent isolation resistors on each signal channel to suppress ground loop noise
    • Power Supply: Passive signal board without independent power consumption, powered by host SBC P2 bus signal power
    • Operating Temperature: Industrial standard -20℃ ~ +70℃ forced air cooling
    • Storage Temperature: -40℃ ~ +85℃; Relative Humidity: 5% ~ 95% RH non-condensing
    • Mechanical Dimension: Single-height 6U VME Eurocard, 233.4mm(H) × 160mm(W) × 18mm(D)
    • Surface Protection: IPC-CC-830 Class 2 conformal coating, gold-plated corrosion-resistant edge connectors
    • Compatible Host SBC: MVME2604, MVME2700, MVME2704, MVME3604, MVME4604 series PowerPC VME controllers
    • Supported RTOS: Matches VxWorks, LynxOS, Embedded Linux for MVME PowerPC platform, no dedicated driver required (passive hardware)
    3. Core Hardware Advantages
    1. Fully passive circuit design, zero power consumption, no heat generation, fanless long-term stable operation
    2. Integrated multi-type communication connectors on front panel, unified field wiring interface for Ethernet, serial and printer signals
    3. One-to-one pin signal mapping without signal attenuation, no delay distortion for real-time industrial data transmission
    4. Comprehensive EMC anti-interference circuit to adapt to high-density multi-card VME cabinet harsh electromagnetic environments
    5. Standard 6U single-height slot design, compatible with all standard VME chassis, convenient hot-swap maintenance without powering off the whole rack
    4. Typical Application Scenarios
    • Thermal power plant VME distributed control cabinet mainboard signal transition wiring module
    • Petrochemical Honeywell TDC3000 DCS PowerPC controller front I/O breakout accessory
    • Aerospace ATE automatic test bench multi-network signal front panel wiring expansion board
    • Railway signal interlock cabinet MVME2700 host communication signal conversion module
    • Industrial real-time monitoring system multi-device network serial wiring auxiliary board
    MOTOROLA / Emerson © AET-3047 6U VME Passive Front Panel Signal Transition Breakout Module


    Write a review

    Tags: MOTOROLA AET-3047 6U VME Front Panel Transition I O Interface Module